When your Clarke Focus II walk-behind scrubber starts leaving a wet stripe or a trail of drips, the squeegee blades are usually worn. The front blade guides water in, the rear blade wipes the floor dry, and the vacuum pulls it up between them. These are Clarke's replacement blades for the Focus II walk-behind, in the two squeegee sizes Nilfisk still stocks:
32.5 in squeegee: Focus II Disc 26. Sold as a front and rear kit or as single blades. The kit costs the same as the rear blade on its own (less, in Linatex), so if the rear is worn, take the kit.
35 in squeegee: Focus II Disc 28, Cylindrical 28 and BOOST 28. Sold as single front and rear blades.
The Disc 34 and BOOST 32 use a 41-inch squeegee. Nilfisk no longer lists 41-inch blades on its parts store, so call us and we'll check what's orderable for your serial number.
| Material |
Best for |
| Urethane |
The factory blade. Resists oils, fats and floor chemicals and lasts longest, which makes it the default for kitchens, warehouses and most commercial floors. |
| Gum rubber |
A soft, flexible blade that wipes smooth floors very dry. The lowest-cost option, but it wears faster on rough concrete and swells with oils. |
| Linatex |
Natural red rubber that stays flexible and grips uneven or textured floors well. A good middle ground between gum and urethane. |
Cut for the Focus II squeegee. The same blades Clarke fits at the factory, so they seat in the frame and seal against the floor.
Front or rear on their own. On the 35 in squeegee, replace just the blade that's worn. On the 32.5 in squeegee, a single front blade costs less than the kit, but a worn rear is the time to buy the kit, since it costs the same and gives you a fresh front too.
Three materials. Stay with urethane or switch to gum or Linatex for your floor.
Check the blades every day, as the Focus II manual asks, and wipe them clean with a cloth. To get at them, loosen the two knobs that hold the squeegee to the machine and pull the assembly off. When a wiping edge rounds over or nicks, unclamp the bands and turn the blade so a fresh edge is in the wiping position, before you buy a new one. Replace the blade once its edges are used up or it tears. Refit the squeegee, and if the rear blade lifts in the middle or at the ends, adjust the tilt screw until the blade flares evenly. Squeegee blades are wear items and aren't covered by Nilfisk's machine warranty except for manufacturing defects.
| Brand |
Clarke (Nilfisk) |
| 32.5 in Kits (front and rear) |
Urethane 11333A, Gum 11336A, Linatex 11339A |
| 32.5 in Single Blades |
Front: urethane 30817U, gum 30817A, Linatex 30817L
Rear: urethane 30816U, gum 30816A, Linatex 30816L |
| 35 in Single Blades |
Front: urethane 30818U, gum 30818A, Linatex 30818L
Rear: urethane 30815U, gum 30815A, Linatex 30815L |
| Fits |
32.5 in: Clarke Focus II Disc 26 (squeegee assembly 10398A)
35 in: Focus II Disc 28, Cylindrical 28 and BOOST 28 (squeegee assembly 10399A) |
| Factory Material |
Urethane, front and rear |
| Does Not Fit |
Focus II Disc 34 and BOOST 32 (41 in squeegee) |
Not sure which part you need? Send us your machine model or serial number, call (855) 601-5678 or email support@oneupcleaning.com, and we'll confirm the fit before you order.
