Skip to content
Clarke 56412191 yellow soft nylon 28-inch cylindrical brush for the Focus II Cylindrical 28

Clarke Focus II Cylindrical 28 Brushes, 28 Inch, Nylon, Poly and Grit

by Clarke
SKU:CLA-56412193
$195.38

Notify me when back in stock

Delivered in 7 to 10 business days Ships direct from Clarke in 3 to 5 business days
  • Authorized Clarke dealerNew equipment, shipped from Clarke
  • Manufacturer warrantyFull coverage from Clarke
  • No sales taxIn every state except Wyoming
  • We beat any priceFound it lower? Call or message us
Questions, a quote or a PO? (855) 601-5678 Message us

Fresh Brushes for Your Focus II Cylindrical 28

The Cylindrical 28 version of the Clarke Focus II walk-behind scrubber scrubs with two counter-rotating roller brushes at 613 RPM. They dig into grout lines and textured tile, and they flick small debris into the tray while they scrub. When the bristles wear short, the deck stops reaching the low spots and the tray fills with water instead of grit. These are Clarke's replacement 28-inch cylindrical brushes, sold one at a time. The machine runs two.

Which Brush Do You Need?

Brush Best for
Polypropylene, red Everyday scrubbing of sealed concrete, VCT and ceramic tile.
Soft nylon, yellow Gentle scrubbing of finished floors and softer tile.
Hard nylon, natural Stiffer bristles for heavier soil and textured floors.
180 grit, blue and grey The lightest abrasive brush, for grout and safety tile that need more bite.
80 grit, black Medium abrasive for rough concrete and quarry tile.
46 grit, orange and brown The most aggressive brush, for embedded grime on rough concrete.

Start with the softest brush that cleans your floor. Grit brushes are abrasive, so test them in a corner and keep them off floor finish you want to keep.

Why Choose a Cylindrical Brush

  • Scrubs and sweeps in one pass. The rollers lift light debris into the tray, so grit doesn't end up under the squeegee.

  • Reaches into grout. Counter-rotating bristles work the floor from both directions.

  • Six bristle choices. From soft nylon to 46 grit, matched to your floor.

Changing and Rotating the Brushes

The Focus II Cylindrical 28 changes brushes without tools. Raise the head and turn the key off. At the front of the machine, loosen the thumb screw on the brush door, lower the door about half an inch and lift it off, then slide the brush out. Slide the new brush onto the driver and turn it slowly until the drive lugs line up with the slots, push it all the way in, refit the door and tighten the thumb screw. Clarke recommends turning each brush end for end now and then to reverse the bristle direction, which makes them last longer. Empty and rinse the debris tray after every shift. Fit the same brush type on both sides. Brushes are wear items and aren't covered by Nilfisk's machine warranty except for manufacturing defects. Disc models use the Focus II disc scrub brushes instead.

Clarke Focus II Cylindrical Brush Specifications

Brand Clarke (Nilfisk)
Part Numbers Polypropylene red 56412046
Soft nylon yellow 56412191
Hard nylon natural 56412192
180 grit blue/grey 56412193
80 grit black 56412194
46 grit orange/brown 56412195
Size 28 in long, 5.75 in (146 mm) diameter
Fits Clarke Focus II Cylindrical 28 walk-behind scrubber
Quantity per Machine 2 (sold individually)
Speed on the Focus II 613 rpm

Document Downloads

Clarke Focus II Mid-Size Operator and Parts Manual (PDF, 5.9 MB)

Not sure which part you need? Send us your machine model or serial number, call (855) 601-5678 or email support@oneupcleaning.com, and we'll confirm the fit before you order.

Frequently Asked Questions

Do these fit my Focus II?

They fit the Focus II Cylindrical 28 walk-behind. Disc and BOOST models use disc brushes or pads instead.

How many brushes do I need?

Two. The deck runs a pair of counter-rotating brushes, and they're sold one at a time.

Which brush should I choose?

Polypropylene for everyday scrubbing, soft nylon for finished floors, and the grit brushes (180, 80 or 46, from lightest to most aggressive) for grout and rough concrete.

How do I make brushes last longer?

Clarke recommends turning each brush end for end now and then to reverse the bristle direction, and rinsing the debris tray after every shift.

Are brushes covered by warranty?

Only for manufacturing defects. Nilfisk treats brushes as wear items.

Got a Question?

(855) 601-5678

We PRICE MATCH

Call us or send us a Message!

Send us a Message

We're SUPER quick!