A guest spilled coffee on the lobby sofa, and the stain has been sitting since breakfast. Cold water lifts the fresh part and leaves a brown ring behind. The Sandia Heated Spotter 3-gallon spot extractor sends solution through a 600 W in-line heater, up to 200°F according to Sandia, so oily and set-in spots release faster.
Every model comes ready to work: 15-foot vacuum and solution hoses and Sandia's 4-inch stainless steel upholstery tool, the tool Sandia specifies for heated machines. You choose a 55 PSI or 100 PSI pump and a standard or Super vacuum motor.
It's built for spot cleaning carpet, upholstery, stairs and vehicle interiors in hotels, offices, schools, healthcare spaces and detail shops, anywhere a full-size extractor is too much machine for the job.
All three share the 3-gallon tanks, the 600 W heater, the 15-foot hoses, the stainless tool and the body. Two choices set them apart.
55 PSI or 100 PSI pump. 55 PSI is plenty for upholstery, car seats and most carpet spots. The 100 PSI pump pushes solution deeper into dense commercial carpet and helps flush out spots that keep wicking back, and it gives you more room when you clean through a longer hose.
Standard or Super motor. The standard 2-stage motor moves 100 CFM with 76 inches of water lift. The Super motor on the 50-4100-SS raises that to 130 CFM and 98.8 inches of lift, per Sandia, so it pulls more water out and the fabric or carpet dries sooner.
|
50-4000 |
50-4100 |
50-4100-SS |
| Pump |
55 PSI |
100 PSI |
100 PSI |
| Vacuum motor |
Standard 2-stage |
Standard 2-stage |
Super |
| Airflow / water lift |
100 CFM / 76 in |
100 CFM / 76 in |
130 CFM / 98.8 in |
| Heater, hoses and tool |
600 W, 15 ft, stainless |
600 W, 15 ft, stainless |
600 W, 15 ft, stainless |
| Price |
$1,434 |
$1,624 |
$1,688 |
The 100 PSI pump adds $190, and the Super motor adds only $64 on top of that. If you're already stepping up to 100 PSI, the 50-4100-SS is the one we'd pick. Not sure? Call (855) 601-5678 or message us with what you clean most and we'll tell you.
The heated spotter ships complete. In the box you get the machine, the 15-foot vacuum and solution hoses with brass quick disconnects, and the stainless hand tool.
4-inch stainless upholstery tool (included). This is the Sandia 10-0501, which sells on its own for $186. Sandia's clear plastic tools are not rated for heat, so stick with stainless on this machine. A spare is handy if two people share one spotter between buildings.
You'll also want a low-foam spotting or extraction chemical, a defoamer for the recovery tank and a pre-spray for heavy soil. Sandia also makes a stainless spotter wand for carpet and a crevice tool. Ask us and we'll add them to your order.
Most heated spotters warm the water in the tank, which takes a while and loses heat as you work. Sandia puts the heater in line, inside its own steel chassis, so the solution heats on its way to the tool. Give it about three minutes to preheat and you're working with hot solution.
The rest of the machine is simple in a good way. The recovery tank comes off with a rotary latch for dumping, and a yellow restrictor pops up when it's full, so you don't suck water into the motor. The slide-out handle and urethane wheels make the 30-pound unit easy to roll down a hotel hallway.
The honest part: 3 gallons is spotter capacity. It's built for stains, upholstery and stairs, not whole rooms. The brass fittings also get hot after a few minutes of spraying, so handle them with care.
600 W in-line heater. Solution up to 200°F, per Sandia, breaks down coffee, grease and body oils that cold water leaves behind.
Complete kit in the box. 15-foot hoses and a stainless upholstery tool, so you can clean the day it arrives.
55 or 100 PSI pump. Pick gentle pressure for fabric or more push for dense carpet.
Full-tank indicator. The yellow restrictor rises when recovery is full, which protects the vacuum motor.
Easy to move. Slide-out handle, double ball-bearing wheels and a molded carry handle for stairs and vans.
Roto-molded body for life. Sandia backs the polyethylene body with a lifetime warranty.
We sell all of these, so here's a straight comparison with the spotters buyers usually weigh against it.
|
Sandia 50-4000 |
EDIC Bravo 339MH-HT |
Tornado Pro Spotter |
| Solution / recovery tanks |
3 / 3 gal |
3 / 3.5 gal |
3.5 / 2.5 gal |
| Pump |
55 PSI (100 PSI on 50-4100) |
55 PSI |
55 PSI |
| Heat |
600 W in-line, up to 200°F |
1,500 W in-tank heater |
No heater |
| Water lift |
76 in (98.8 in on Super) |
106 in |
89 in |
| Hoses and tool |
15 ft hoses, stainless tool |
Auto detailing hose and tool kit |
13 ft hose, clear tool |
| Warranty |
Lifetime body, 2 yr motor and pump |
5 yr parts and labor, lifetime housing |
2 yr parts and labor, 10 yr tank |
| Price |
$1,434 |
$1,862 |
$999 |
The EDIC Bravo has more water lift and a longer warranty, and it costs $430 more in its heated kit. If you don't need heat at all, the Tornado Pro Spotter saves you $440. The Sandia sits between them: real in-line heat, a stainless tool and 15-foot hoses in the box, and a body made in the USA. Don't need heat? The Sandia Spotter 50-1000 is the same 3-gallon machine without the heater, from $928. Detailers also ask about the Sandia Indy 50-7000: it's built on the same platform as the 50-4000 (3-gallon tanks, 55 PSI pump, 100 CFM motor, 600 W heater, 15 ft hoses and stainless tool) and sold as part of Sandia's automotive line, so the 50-4000 here gets you the same machine. See every option in our carpet spotters collection.
Connect the hoses at the brass quick disconnects, fill the solution tank, plug in and switch on the heater. Sandia recommends about three minutes of preheat. Alternate spraying and vacuuming as you work so hot solution keeps moving through the line, and turn the heater off if you stop spraying for more than a few minutes.
Use low-foam chemicals and keep defoamer in the recovery tank. After each job, dump and rinse the recovery tank, run clean water through the tool, and let the tanks air dry. The operating manual below has the full parts list if you ever need a pump, motor or heater part.
Sandia spotters are built in Huntington Beach, California, and Sandia describes them as manufactured in the USA with globally sourced components. The roto-molded bodies carry a lifetime warranty, and the pumps, motors and heater parts are sold through Sandia's distributor network, so a worn part doesn't mean a new machine.
