The customer's SUV is parked in the driveway, a juice box leaked into the back seat last week, and the only outlet is on the garage wall. The Sandia 50-7000 is made for that job. It's the 3-gallon heated spotter in Sandia's Indy automotive line, it heats solution up to 200°F according to Sandia, and it runs the motor, pump and heater on one power cord.
It ships ready to work, with 15-foot vacuum and solution hoses and Sandia's 4-inch stainless steel upholstery tool. The machine weighs 30 pounds (40 boxed, per Sandia), so one person lifts it into a van, and the 15-foot hoses let it sit outside the car door while you work the seats, mats and carpet.
If you detail out of a van, this is the Indy I'd look at first. It's the smallest machine in Sandia's automotive line, and the 600 W heater sits in line between the pump and the hose, so the solution heats on its way to the tool instead of waiting in the tank. Fill it with warm tap water, not hot: Sandia's manual sets a 120°F limit for the tank, and the heater does the rest.
I like the small details. The red recovery tank lifts off with a rotary latch for dumping, and a foam float cuts the suction when it's full. You'll hear the motor change pitch, which is your cue to empty it.
The honest part: 3 gallons is spotter capacity. It handles seats, mats and spot work all day, but if your shop does full interiors on minivans back to back, the bigger Sandia Indy 6 and 12-gallon extractors will save you a lot of trips to the sink.
In-line heat up to 200°F. Sandia rates the 600 W heater at solution up to 200°F, which breaks down grease and body oils that cold water leaves behind.
One cord for everything. Pump, vacuum and heater all run off a single 20-foot cord, so one garage outlet is enough.
Ready on day one. The 15-foot hoses and the stainless upholstery tool are in the box, and stainless is the tool Sandia specifies for heated machines.
Light enough for a van. 30 pounds and 21 x 10 x 24 inches, with a slide-out handle and double ball-bearing urethane wheels.
Full-tank warning. A float in the recovery tank cuts the suction when it's full, which keeps water out of the vacuum motor.
Roto-molded body. Sandia covers the polyethylene body with a limited lifetime warranty, plus 2 years on the vacuum motor and pump.
Best fit: mobile detailers who clean in customers' driveways and parking lots, small shops that mostly do seats, mats and spot work, and dealership or car wash bays that want a heated spotter they can roll from car to car.
Not the right machine for full interiors back to back on a busy line, because 3-gallon tanks mean frequent refills. There, the Sandia Indy 6 and 12-gallon extractors do the same job with bigger tanks, a 100 PSI pump and a 1,200 W heater. It's also not a room carpet machine: 55 PSI and 76 inches of water lift are spotter numbers, made for upholstery and vehicle carpet.
The Indy line by price: the 3-gallon 50-7000 at $1,468, the 6-gallon 86-4000-H at $2,858 and the 12-gallon 80-4000-H at $3,098. See every option on our auto detailing extractors page.
We sell both, so here's a straight comparison with the heated spotter detailers most often weigh against it.
|
Sandia 50-7000 Indy |
EDIC Bravo 339MH-HT |
| Solution / recovery tanks |
3 / 3 gal |
3 / 3.5 gal |
| Pump |
55 PSI |
55 PSI |
| Heat |
600 W in-line, up to 200°F |
1,500 W in-tank, 150°F |
| Water lift |
76 in |
106 in |
| Hoses and tool |
15 ft hoses, stainless tool |
8 ft hose, stainless tool |
| Weight |
30 lb |
19 lb |
| Warranty |
Lifetime body, 2 years motor and pump |
5 years parts and labor, lifetime housing |
| Price |
$1,468 |
$1,862 |
The EDIC Bravo pulls harder, weighs less and carries the longer warranty, and it costs about $390 more. The Indy's case is hotter solution, hoses nearly twice as long, so the machine can stay outside the car, and the lower price.
Before the first job. Sandia ships its spot extractors with antifreeze in the pump and lines. Spray a quart of warm water through the hand tool to flush it out.
Every job. Fill the solution tank with warm water, under 100°F as Sandia's manual recommends, and a liquid carpet or upholstery detergent mixed to its label. Run the pump and spray until solution comes out of the tool before you switch on the heater, so the heater is never dry. Keep defoamer in the recovery tank, because foam carries moisture into the vacuum motor.
After the job. Rotate the latch, lift off the recovery tank and pour it out through the vacuum inlet, not the hatch. If the machine is stored where it can freeze, drain the heater lines first. Sandia warns that a frozen heater can crack, and the warranty doesn't cover it.
If something's off. Lost suction usually means the float is stuck or the hose cuff is loose, so open the screw cap, push the float down and reseat the cuff. Weak spray usually means a clogged jet or intake, so take the jet off the tool and squeeze the trigger, then clean the intake in the solution tank and the quick disconnect. Keep solvents, citrus acids and harsh degreasers out of the machine, and don't use it as a dry vacuum.
Ultimate Solutions builds Sandia machines in Huntington Beach, California, where final assembly, quality control and warranty service all happen. Sandia stocks replacement parts in the US and says they typically ship within 24 hours, which matters when a machine on a detail route goes down.