Skip to content

Tornado® Standard Brushes for Vortex 13 CRB Floor Scrubber, 93120.1 (Pair)

by Tornado
SKU:93120.1
$152.99

Notify me when back in stock

Delivered in 5 to 8 business days Ships direct from Tornado in 1 to 3 business days
  • Authorized Tornado dealerNew equipment, shipped from Tornado
  • Manufacturer warrantyFull coverage from Tornado
  • No sales taxIn every state except Wyoming
  • We beat any priceFound it lower? Call or message us
Questions, a quote or a PO? (855) 601-5678 Message us

Fits:

  • Tornado Vortex 13 (TS050-W13-U)
  • 2 standard brushes, the pair the machine ships with
  • First-time cleaning on tile, wood, rubber and vinyl

Fresh Standard Brushes for Your Tornado Vortex 13


These are the brushes your Tornado Vortex 13 ships with, and Tornado lists them as its replacement part. When the bristles on your current pair are worn short or bent out of shape, a fresh pair brings back the scrubbing action the machine was built around.

Tornado's brush chart makes the standard pair the first choice for first-time cleaning on grouted tile, ceramic, mosaic, wood, sports floors, rubber and vinyl tile. It's also the brush Tornado recommends for routine maintenance on smooth concrete. For most crews, this is the pair that stays in the machine day to day.

You can tell it's time for new brushes when the scrub result drops even after you've stepped up the brush contact. The Vortex 13 adjusts brush contact in 4 steps to make up for wear, and Tornado's troubleshooting table says to check brush pressure first, then replace the brushes if needed.

The standard brushes come as a pair, one for the front shaft and one for the rear. The front brush does most of the scrubbing; the rear brush finishes the job and collects the remaining water, so both are replaced together.


Tornado makes four brush pairs for the Vortex 13:


Which Vortex 13 Brush Do You Need?

Floor First-time cleaning Maintenance cleaning
Grouted tile, ceramic, mosaic, wood, sports floors, rubber, vinyl tile Standard Soft
Short pile carpet Soft/Carpet Soft/Carpet
Marble, granite, slate Soft Soft
Smooth concrete Hard Standard

Source: Tornado Vortex 13 operator manual, brush selection chart. Other floors: choose to suit the floor's condition.


Swapping Brushes Without Tools

Per Tornado's manual: switch the machine off and unplug it, then pull the two brush shafts. They're held by quick-release retaining balls, so no tools are needed. Slide the brushes off, fit the new pair, and push each shaft back in from the right-hand side of the machine (the side with the power cable and foot pedal), which Tornado notes is the easier way in.

The small multicolored plastic plugs on the brushes are there to identify them, so you can keep a set for each area of a building and avoid carrying soil from one area to another.


Make Your Brushes Last

  • Wash the brushes regularly. Dip them in a bucket or sink, or rinse them under running water.

  • Store spare pairs standing vertically so the bristles don't bend.

  • Don't leave the brushes fitted on a machine that sits idle for days. The bristles take a set in one direction; if that happens, reverse the brush so they can flex back.

  • Always move the machine in transport mode. Transporting it with the brush control in the working position damages the brushes.


Add the 93049 side brush for edges along baseboards, and the Tornado transport cart for moving the machine between floors. Running the larger Vortex 18? It takes 18 in brushes, such as the standard pair for the Vortex 18.

Not sure which Vortex you have? Call (855) 601-5678 or send us a message with your machine's model number and we'll confirm the fit. See every Tornado line on our Tornado page.

These Standard Brushes (93120.1) are Compatible with:


Vortex 13 Standard Brushes Specifications
Manufacturer Tornado
Model Number 93120.1
Product Type Floor Scrubber Part, Cylindrical Brushes
Brush Type Standard
Color Black
Sold As Pair (2 brushes, front and rear)
Brush Width 13 in
Brush Speed on the Vortex 13 650 RPM
Mounting On the brush shafts, quick-release retaining balls
Compatible with Tornado® Vortex 13 Scrubber, #TS050-W13-U


Downloads


Frequently Asked Questions

Are these the same brushes that came with my Vortex 13?

Yes. The standard pair (93120.1) is the set the Vortex 13 ships with, and Tornado lists it as the machine's replacement brush part.

When should I replace the brushes?

The Vortex 13 adjusts brush contact in 4 steps to make up for bristle wear. When stepping up the contact no longer brings the scrub result back, or the bristles are worn short or permanently bent, it's time for a new pair.

Do I need to replace both brushes?

Yes, the brushes are sold and fitted as a pair. The front brush does most of the scrubbing and the rear brush finishes and collects the water, so replacing both keeps the machine scrubbing and drying evenly.

Do these fit the Vortex 18 or Vortex 9?

No. These are 13 in brushes for the Vortex 13 (TS050-W13-U) only. The Vortex 18 and Vortex 9 take their own brush sizes.


Got a Question?

(855) 601-5678

We PRICE MATCH

Call us or send us a Message!

Send us a Message

We're SUPER quick!